12V Plastic Water Solenoid Valve

#ad
Adafruit Industries 997 #ad - There are two 1/2\" Nominal NPS outlets. The valve has a gasket arrangement inside, so there is a minimum pressure requirement of 002 mpa 3 pSI. Control the flow of fluid using the flow of electrons! This liquid valve would make a great addition to your robotic gardening project. These solenoids are not rated for food safety or use with anything but water.

Voltage current6v 160 ma7v 190 ma8v 220 ma9v 240 ma10v 270 ma11v 300 mA12V 320 mA Easily control the flow of water. Also, liquid can only flow one direction. We suggest a tip120 or n-channel power FET with a 1N4001 kickback diode to drive this from a microcontroller pin. When 12vdc is applied to the two terminals, the valve opens and water can push through.

12V Plastic Water Solenoid Valve #ad - Requires 3 psi water pressure to operate not a lot of pressure. Normally, the valve is closed. We tried this solenoid at various DC voltages and found we could actuate it down at 6VDC although it was a little slower to open. For a power supply, our 9v 1A or 12V 1A power adapters will do the job. Here is the current draw table for various voltages.

. Perfect for your Arduino powered gardening project.

Weitere Informationen zu Adafruit Industries 997 #ad

XCSOURCE 5pcs Soil Moisture Sensor And Automatic Watering System for Arduino TE215

#ad
XCSOURCE TE215 #ad - The digital output d0 can be connected directly with the microcontroller to detect high and low by the microcontroller to detect soil moisture. Analog output ao and ad module connected through the AD converter, you can get more precise values of soil moisture. Interface description 4-wire: VCC: 3. 3v-5v gnd: gnd do: digital output interface 0 and 1 ao: analog output interface Instructions for Use: Soil moisture module is most sensitive to the ambient humidity is generally used to detect the moisture content of the soil.

XCSOURCE 5pcs Soil Moisture Sensor And Automatic Watering System for Arduino TE215 #ad - Package includes: 5 pcs soil moisture detector Module 5 Set of Jumper Cables 2 in 1 This is a simple water sensor that can be used to detect soil moisture. Can be used in module plant waterer device, and the plants in your garden no need people to manage. This is a must have tool for a connected garden! It will be helpful to remind you to water your indoor plants or to monitor the soil moisture in your garden.

Operating voltage: 3. 3v-5v. The digital outputs do shop relay module can directly drive the buzzer module, which can form a soil moisture alarm equipment. Module dual output mode, digital output, analog output more accurate.

Weitere Informationen zu XCSOURCE TE215 #ad


Similar products:

• 12V Plastic Water Solenoid Valve #ad
• JBtek 4 Channel DC 5V Relay Module for Arduino Raspberry Pi DSP AVR PIC ARM #ad
• Gowoops 5 PCS of Temperature Humidity Sensor Module Digital DHT11 for Arduino Raspberry Pi 2 3 #ad
• SainSmart 4-Channel Relay Module #ad
• DFROBOT Gravity: Analog Capacitive Soil Moisture Sensor- Corrosion Resistant #ad
• Decdeal Submersible Water Pump DC 12V 5W Ultra-quiet Pump for Pond, Aquarium, 280L/H Lift 300cm #ad
• Elite Silicone Airline Tubing for Aquarium, 10-Feet, Blue #ad
• DIGITEN DC 12V 1/4" Inlet Feed Water Solenoid Valve Quick Connect N/C normally Closed #ad
• Haitronic 120pcs 20cm Length Jumper Wires/Dupont Cable Multicolored(10 Color) 40pin M to F, 40pin M to M, 40pin F to F for Breadboard/Arduino Based/DIY/ Raspberry Pi 2 3/Robot Ribbon Cables Ki #ad
• Gowoops 2 PCS DHT22 Temperature Humidity Sensor Module Digital Measurement for Arduino Raspberry Pi 2 3 #ad

JBtek 4 Channel DC 5V Relay Module for Arduino Raspberry Pi DSP AVR PIC ARM

#ad
JBtek 4450182 #ad - Application:supports all mCU control, PLC control, The industrial field, Smart home control. Indication LED's for Relay output status. Module dual output mode, digital output, analog output more accurate. Equiped with high-current relay, AC250V 10A ; DC30V 10A. It can be controlled directly by micro-controller raspberry pi, dsp, avr, arm, MSP430, ARM, PIC, Arduino, 8051, TTL logic This is a simple water sensor that can be used to detect soil moisture.

JBtek 4 Channel DC 5V Relay Module for Arduino Raspberry Pi DSP AVR PIC ARM #ad - Can be used in module plant waterer device, and the plants in your garden no need people to manage. This is a must have tool for a connected garden! It will be helpful to remind you to water your indoor plants or to monitor the soil moisture in your garden. Operating voltage: 3. 3v-5v. Be able to control various appliances, and other equipments with large current.

5v relay module 4-channelThis is a 5V 4-Channel Relay interface board. 5v 4-channel relay interface board, and each one needs 50-60mA Driver Current.

Weitere Informationen zu JBtek 4450182 #ad


Similar products:

• XCSOURCE 5pcs Soil Moisture Sensor And Automatic Watering System for Arduino TE215 #ad
• Haitronic 120pcs 20cm Length Jumper Wires/Dupont Cable Multicolored(10 Color) 40pin M to F, 40pin M to M, 40pin F to F for Breadboard/Arduino Based/DIY/ Raspberry Pi 2 3/Robot Ribbon Cables Ki #ad
• JBtek 8 Channel DC 5V Relay Module for Arduino Raspberry Pi DSP AVR PIC ARM #ad
• Adafruit Si7021 Temperature & Humidity Sensor Breakout Board (3251) #ad
• Elegoo EL-CP-004 120pcs Multicolored Dupont Wire 40pin Male to Female, 40pin Male to Male, 40pin Female to Female Breadboard Jumper Wires Ribbon Cables Kit for arduino #ad
• Kuman 5PCS Soil Moisture Sensor Kit Compatible with Raspberry pi Arduino Uno R3 Mega 2560 with 10PIN Female to Female Jump Cables 20PIN Male to Female DuPont Jump Cable Automatic Watering System KY70 #ad
• GenBasic 80 Piece Female to Female 4 and 8 Inch Solderless Ribbon Dupont-Compatible Jumper Wires for Breadboard Prototyping #ad
• Uxcell BWDYM DC Power Cable Female Connector Plug (Pack of 10) #ad
• McIgIcM 3pcs 2 Channel DC 5V Relay Module for Arduino UNO R3 DSP ARM PIC AVR STM32 Raspberry Pi with Optocoupler Low Level Trigger Expansion Board #ad
• 2 Pack 120mm White LED Case Fan Cooling PC and Light Up Computer Case with Cool Look, Long Life Bearing with DC 15 LED Illuminating PC Case. Quiet Durable Fans Enhance Performance of Tower #ad

DIGITEN G1/2" Water Flow Hall Sensor Switch Flow Meter Flowmeter Counter 1-30L/min

#ad
DIGITEN #ad - Cable length:15cm. Flow range:1-30L/min. Waterproof, pressure resistance, Heat resistance, cold resistance. Frequency: F=7. 5 * q l / min error: ± 2% voltage :3. 5-24vdc, current can not exceed 10ma, 450 output pulses/liters, f=onstant * units of flow l / min * time seconds flow range:1-30l/min maximum current:15 mADC 5V Working voltage range:DC 5-24 V Load capacity:≤10 mADC 5V Operating Temp:≤80℃, Operating humidity:35%-90%RH Allow compression:Water pressure 1.

75 mpa below insulation resistance:>100m ohm storage temperature:-25-80℃ Storage humidity:25%-95%RH Output Waveform:Square Wave, output pulse singal. Be able to control various appliances, and other equipments with large current. Application:supports all mCU control, The industrial field, PLC control, Smart home control.

DIGITEN G1/2" Water Flow Hall Sensor Switch Flow Meter Flowmeter Counter 1-30L/min #ad - Indication LED's for Relay output status. Packaging include flowmeter x 1 This is a simple water sensor that can be used to detect soil moisture. Can be used in module plant waterer device, and the plants in your garden no need people to manage. This is a must have tool for a connected garden! It will be helpful to remind you to water your indoor plants or to monitor the soil moisture in your garden.

Operating voltage: 3. 3v-5v.

Weitere Informationen zu DIGITEN #ad


Similar products:

• 12V Plastic Water Solenoid Valve #ad
• DIGITEN G1" Water Flow Hall Effect Sensor Switch Flow Meter Flowmeter Counter 1-60L/min #ad
• DIGITEN 1/4 Quick Connect 0.3-10L/min Water Hall Effect Flow Sensor Meter #ad
• Motorized Ball Valve- 1/2" Stainless Steel Electrical Ball Valve with Full Port, 9-24V AC/DC and 3 Wire Setup by U.S. Solid #ad
• JBtek 4 Channel DC 5V Relay Module for Arduino Raspberry Pi DSP AVR PIC ARM #ad
• DIGITEN G3/8 Water Flow Hall Sensor Switch Flow Meter Flowmeter Counter 0.3-10L/min #ad
• JBtek 8 Channel DC 5V Relay Module for Arduino Raspberry Pi DSP AVR PIC ARM #ad
• HFS 110v Ac or 12v Dc Electric Solenoid Valve Water Air Gas, Fuels N/c - 1/4", 1/2", 3/4", 1" NPT Available (12V DC 1/2" NPT) #ad
• DIGITEN DC 12V 1/4" Inlet Feed Water Solenoid Valve Quick Connect N/C normally Closed #ad
• Water Flow Sensor Flowmeter Hall Flow Sensor Water control 1-30L/min by Generic #ad

DFROBOT Gravity: Analog Capacitive Soil Moisture Sensor- Corrosion Resistant

#ad
DFRobot SEN0193 #ad - The following image shows an example project - a device that notifies you when a plant needs to be watered. It is made of a corrosion resistant material giving it a long service life. To make it compatible with a Raspberry Pi, an ADC converter is required. Allow compression:Water pressure 1. 75 mpa below. 5v 4-channel relay interface board, and each one needs 50-60mA Driver Current.

Working voltage range:DC 5-18 V. It is made of a corrosion resistant materal giving it a long service life. This sensor is compatible with our 3-pin "Gravity" interface, which means it can be directly connected to the Gravity I/O Expansion Shield. Application:supports all mCU control, The industrial field, PLC control, Smart home control.

DFROBOT Gravity: Analog Capacitive Soil Moisture Sensor- Corrosion Resistant #ad - Indication LED's for Relay output status. This module includes an on-board voltage regulator which gives it an operating voltage range of 3. 3 ~ 5. 5v. Insert it into soil and impress your friends with the real-time soil moisture data. This sensor is compatible with dfRobot 3-pin "Gravity" interface, which can be directly connected to the Gravity I/O expansion shield.

Weitere Informationen zu DFRobot SEN0193 #ad


Similar products:

• 12V Plastic Water Solenoid Valve #ad
• XCSOURCE 5pcs Soil Moisture Sensor And Automatic Watering System for Arduino TE215 #ad
• Kuman 5PCS Soil Moisture Sensor Kit Compatible with Raspberry pi Arduino Uno R3 Mega 2560 with 10PIN Female to Female Jump Cables 20PIN Male to Female DuPont Jump Cable Automatic Watering System KY70 #ad
• HONG111 5pcs TE215 Dual Mode High Sensitivity Soil Moisture Sensor, Auto Arduino Sensor Module Watering System Manager 3.3V-5V #ad
• Adafruit MCP3008 8-Channel 10-Bit ADC With SPI Interface for Raspberry Pi #ad
• DIGITEN DC 12V 1/4" Inlet Feed Water Solenoid Valve Quick Connect N/C normally Closed #ad
• JBtek 4 Channel DC 5V Relay Module for Arduino Raspberry Pi DSP AVR PIC ARM #ad
• TraGoods Analog Capacitive Soil Moisture Sensor, Corrosion Resisting, Wide Voltage Module for Arduino - Arduino Compatible SCM & DIY Kits - Module Board, for Garden Plants Moisture Detection #ad
• Decdeal Submersible Water Pump DC 12V 5W Ultra-quiet Pump for Pond, Aquarium, 280L/H Lift 300cm #ad
• Gowoops 2 PCS DHT22 Temperature Humidity Sensor Module Digital Measurement for Arduino Raspberry Pi 2 3 #ad

Kuman 5PCS Soil Moisture Sensor Kit Compatible with Raspberry pi Arduino Uno R3 Mega 2560 with 10PIN Female to Female Jump Cables 20PIN Male to Female DuPont Jump Cable Automatic Watering System KY70

#ad
Kuman KY70-US #ad - The example project of the soil moisture Sensor Module working with Arduino Uno R3 and Raspberry pi can be provided free by Email, please contact us via Amazon. Working voltage range:DC 5-18 V. 5v 4-channel relay interface board, and each one needs 50-60mA Driver Current. Insert it into soil and impress your friends with the real-time soil moisture data.

Kuman soil moisture module, can improve the electrical conductivity, to prevent touch the soil is easy to rust, the surface using nickel-plated treatment, widened sensor area, and increase of service life. Through adjusting the potentiometer to control the soil humidity threshold, control the flower pot soil moisture, garden, can automatic watering the vegetable garden, all of electronic competitions and for the Arduino Raspberry pi design etc.

Kuman 5PCS Soil Moisture Sensor Kit Compatible with Raspberry pi Arduino Uno R3 Mega 2560 with 10PIN Female to Female Jump Cables 20PIN Male to Female DuPont Jump Cable Automatic Watering System KY70 #ad - This is a must have tool for a connected garden! It will be helpful to remind you to water your indoor plants or to monitor the soil moisture in your garden. Output waveform:Square Wave, output pulse signal. Sensor:Hall effect. Module dual output mode, digital output, analog output more accurate. Equiped with high-current relay, AC250V 10A ; DC30V 10A.

Flow range:1-30L/min. It is made of a corrosion resistant material giving it a long service life.

Weitere Informationen zu Kuman KY70-US #ad


Similar products:

• DFROBOT Gravity: Analog Capacitive Soil Moisture Sensor- Corrosion Resistant #ad
• 12V Plastic Water Solenoid Valve #ad
• JBtek 4 Channel DC 5V Relay Module for Arduino Raspberry Pi DSP AVR PIC ARM #ad
• Decdeal Submersible Water Pump DC 12V 5W Ultra-quiet Pump for Pond, Aquarium, 280L/H Lift 300cm #ad
• Microchip MCP3008-I/P 10-Bit ADC with SPI (Pack of 4) #ad
• Adafruit MCP3008 8-Channel 10-Bit ADC With SPI Interface for Raspberry Pi #ad
• Gowoops 2 PCS DHT22 Temperature Humidity Sensor Module Digital Measurement for Arduino Raspberry Pi 2 3 #ad
• HiLetgo 5pcs DHT11 Temperature and Humidity Sensor Module for Arduino Raspberry Pi 2 3 #ad
• DIGITEN DC 12V 1/4" Inlet Feed Water Solenoid Valve Quick Connect N/C normally Closed #ad
• Learn To Brew LLC Food Grade Vinyl Tubing - 10 feet 5/16 ID - 7/16 OD #ad

DIGITEN DC 12V 1/4" Inlet Feed Water Solenoid Valve Quick Connect N/C normally Closed

#ad
DIGITEN #ad - Be able to control various appliances, and other equipments with large current. The rated voltage is DC 12V. This sensor is compatible with dfRobot 3-pin "Gravity" interface, which can be directly connected to the Gravity I/O expansion shield. Dc 12v 1/4" quick connect Solenoid valve. Turn on water when system start;and cut off water when system stop.

Working pressure:002-08mpa. Rated power:4. 8w. It will become hot because there are so many coils inside. Kuman soil moisture module, the surface using nickel-plated treatment, widened sensor area, to prevent touch the soil is easy to rust, can improve the electrical conductivity, and increase of service life.

DIGITEN DC 12V 1/4" Inlet Feed Water Solenoid Valve Quick Connect N/C normally Closed #ad - Through adjusting the potentiometer to control the soil humidity threshold, control the flower pot soil moisture, garden, can automatic watering the vegetable garden, all of electronic competitions and for the Arduino Raspberry pi design etc. This is a must have tool for a connected garden! It will be helpful to remind you to water your indoor plants or to monitor the soil moisture in your garden.

But this operation is unreasonable. It's safe voltage for people. Food quality and suitable for Reverse Osmosis water system, etc. Insert it into soil and impress your friends with the real-time soil moisture data.

Weitere Informationen zu DIGITEN #ad


Similar products:

• Neeshow 1/4" OD Quick Connect Push In to Connect Water Tube Fitting Set Of 20 (Y+T+I+L Type Combo) #ad
• uxcell 5 Pieces ZP4510 Liquid Water Level Sensor Vertical Float Switches #ad
• DIGITEN 1/4 Quick Connect 0.3-10L/min Water Hall Effect Flow Sensor Meter #ad
• Anndason 6 Pieces Black Water Level Sensor Aquarium Tank Side Mounted Horizontal Liquid Float Switch #ad
• Malida Equal Straight OD Tube Ball Valve Quick Connect Fitting 1/4-Inch by 1/4-Inch OD Valve Start RO Water System Set Of 5 #ad
• cck cck-2 Malida Size 1/4 Inch, 10 Meters 30 feet Length Tubing Hose Pipe for RO Water Filter System (blue) #ad
• Malida 1/4" inch White Fittings Bulkhead Connector Tube Quick Connect for RO Unit (Pack of 5) #ad
• Malida Water Pressure Gauge Stainless For Aquarium Meter 0-1.6MPa 0-220psi Reverse Osmosis System Pump With 1/4 #ad
• Malida 1/4" Tee 3 Way Tube Quick Connect Push Fit RO Water Reverse Osmosis System set of 10 #ad
• 12V Plastic Water Solenoid Valve #ad

Major Brands TIP120-R Transistor, Tip 120, NPN Power, Darlington Pack of 10

#ad
Major Brands TIP120-R #ad - Application:supports all mCU control, The industrial field, PLC control, Smart home control. Indication LED's for Relay output status. The product type is major brands tip120-R Transistor, NPN Power, Tip 120, Darlington. Working voltage range:DC 5-18 V. This is a simple water sensor that can be used to detect soil moisture.

Major Brands TIP120-R Transistor, Tip 120, NPN Power, Darlington Pack of 10 #ad - Can be used in module plant waterer device, and the plants in your garden no need people to manage. This is a must have tool for a connected garden! It will be helpful to remind you to water your indoor plants or to monitor the soil moisture in your garden. Operating voltage: 3. 3v-5v. It is made of a corrosion resistant material giving it a long service life.

Dc 12v 1/4" quick connect Solenoid valve. Turn on water when system start;and cut off water when system stop. Working pressure:002-08mpa. Rated power:4. 8w. It will become hot because there are so many coils inside.

Weitere Informationen zu Major Brands TIP120-R #ad


Similar products:

• 12V Plastic Water Solenoid Valve #ad
• Ltvystore 100PCS 10Value (1N4001~1N5819) Diode Assorted Kit Set with Clear Box #ad
• L7805CV L7805 Positive Voltage Regulator Output 5v TO-220 Package, 20 Pieces #ad
• Uxcell a14092600ux0438 Open Frame Actuator Linear Mini Push Pull Solenoid Electromagnet, DC 4.5V, 40 g/2 mm #ad
• goeasybuy 100x 1N4001 Molded Plastic Case Rectifier Diodes, 1A, 50V DO-41 #ad
• ELEGOO for Arduino Nano V3.0, Nano Board CH340/ATmega328P Without USB Cable, Compatible with Arduino Nano V3.0 (Nano x 3 Without Cable) #ad
• Major Brands IRF540 Transistor, MOSFET, N-Channel, 100 V (Pack of 5) #ad
• 10 Pcs Complete TO-220 Heatsink Kit, by Tech Express #ad
• Elegoo EL-CB-001 UNO R3 Board ATmega328P ATMEGA16U2 with USB Cable for Arduino #ad
• McIgIcM rectifier diode assorted kit,100pcs 1N4148 1N4007 1N5819 1N5399 1N5408 1N5822 FR107 FR207 electronic components package,diode assortment #ad

HONG111 5pcs TE215 Dual Mode High Sensitivity Soil Moisture Sensor, Auto Arduino Sensor Module Watering System Manager 3.3V-5V

#ad
HONG111 #ad - Module dual output mode, digital output, analog output more accurate. Equiped with high-current relay, AC250V 10A ; DC30V 10A. Product type: Transistor. Attention: 1. Soil moisture module is most sensitive to the ambient humidity is generally used to detect the moisture content of the soil. This sensor is compatible with dfRobot 3-pin "Gravity" interface, which can be directly connected to the Gravity I/O expansion shield.

Specification: Operating voltage: 3. 3v~5v. With power indicator red and digital switching output indicator green. The digital outputs do shop relay module can directly drive the buzzer module- which can form a soil moisture alarm equipment. A fixed bolt hole for easy installation. 2. Module output is high level when the soil moisture deficit, or output is low.

HONG111 5pcs TE215 Dual Mode High Sensitivity Soil Moisture Sensor, Auto Arduino Sensor Module Watering System Manager 3.3V-5V #ad - Output waveform:Square Wave, output pulse signal. Sensor:Hall effect. Package included : 5 pcs soil moisture detector Module 5 Set of Jumper Cables 2 in 1 This is a simple water sensor that can be used to detect soil moisture. Can be used in module plant waterer device, and the plants in your garden no need people to manage.

This is a must have tool for a connected garden! It will be helpful to remind you to water your indoor plants or to monitor the soil moisture in your garden.

Weitere Informationen zu HONG111 #ad


Similar products:

• Gowoops 5 PCS of Temperature Humidity Sensor Module Digital DHT11 for Arduino Raspberry Pi 2 3 #ad
• Decdeal Submersible Water Pump DC 12V 5W Ultra-quiet Pump for Pond, Aquarium, 280L/H Lift 300cm #ad
• DFROBOT Gravity: Analog Capacitive Soil Moisture Sensor- Corrosion Resistant #ad
• Gikfun Capacitive Soil Moisture Sensor Corrosion Resistant for Arduino Moisture Detection Garden Watering DIY (Pack of 2PCS) EK1940 #ad
• Gowoops 2 PCS DHT22 Temperature Humidity Sensor Module Digital Measurement for Arduino Raspberry Pi 2 3 #ad
• 12V Plastic Water Solenoid Valve #ad
• WINGONEER 5PCS KY-019 5V One Channel Relay Module Board Shield for PIC AVR DSP ARM for arduino Relay #ad
• HiLetgo 5pcs DHT11 Temperature and Humidity Sensor Module for Arduino Raspberry Pi 2 3 #ad
• Learn To Brew LLC Food Grade Vinyl Tubing - 10 feet 5/16 ID - 7/16 OD #ad
• HiLetgo 2pcs ESP8266 NodeMCU LUA CP2102 ESP-12E Internet WiFi Development Board Open Source Serial Wireless Module Works Great with Arduino IDE/Micropython (Pack of 2PCS) #ad

uxcell 5 Pieces ZP4510 Liquid Water Level Sensor Vertical Float Switches

#ad
Uxcell a13082200ux0389 #ad - Working voltage range:DC 5-18 V. This sensor is compatible with dfRobot 3-pin "Gravity" interface, which can be directly connected to the Gravity I/O expansion shield. This analog capacitive soil moisture sensor measures soil moisture levels by capacitive sensing, rather than resistive sensing like other types of moisture sensor.

Module dual output mode, digital output, analog output more accurate. Equiped with high-current relay, AC250V 10A ; DC30V 10A. Thread diaapprox : 9. 5mm / 09" x 2. 27"max d*h;cable length : 36cm / 0374";switch body Size : 23. 3 x 57. 7mm / 14. 2". Color : white;net weight : 70g;Package Content : 5 x Water Level Sensor.

uxcell 5 Pieces ZP4510 Liquid Water Level Sensor Vertical Float Switches #ad - Max contact resistance : 100m ohm;temperature rating : -10 / +85 Celsuis;Float Ball Material : P. P;float body Material : P. P. 5v 4-channel relay interface board, and each one needs 50-60mA Driver Current. The switch may actuate a pump, an alarm, an indicator, or other device.

Weitere Informationen zu Uxcell a13082200ux0389 #ad


Similar products:

• DIGITEN DC 12V 1/4" Inlet Feed Water Solenoid Valve Quick Connect N/C normally Closed #ad
• Uxcell a11063000ux0053 DPDT HH52P Coil 8 Pin General Purpose Relay with PYF08A Socket, DC 12V #ad
• Uxcell a15062300ux0219 IEC255 DC 12V Coil 8Pin DPDT Electromagnetic Power Relay with Socket Base #ad
• uxcell DC 12V Coil Power Relay 10A DPDT LY2NJ with PTF08A Socket Base #ad
• 12V Plastic Water Solenoid Valve #ad
• TOM Aquarium Aqua Lifter Pump 3.5gph flow rate to 30 inches height #ad
• Decdeal Submersible Water Pump DC 12V 5W Ultra-quiet Pump for Pond, Aquarium, 280L/H Lift 300cm #ad
• INTLLAB 12V DC DIY Peristaltic Liquid Pump Dosing Pump for Aquarium Lab Analytical 3mm ID x 5mm OD #ad
• Anndason 6 Pieces Black Water Level Sensor Aquarium Tank Side Mounted Horizontal Liquid Float Switch #ad
• Neeshow 1/4" OD Quick Connect Push In to Connect Water Tube Fitting Set Of 20 (Y+T+I+L Type Combo) #ad

Decdeal Submersible Water Pump DC 12V 5W Ultra-quiet Pump for Pond, Aquarium, 280L/H Lift 300cm

#ad
Anself H10448 #ad - Insert it into soil and impress your friends with the real-time soil moisture data. It is made of a corrosion resistant material giving it a long service life. Please cut off the power before you install/put in/take away the pump from the water; otherwise, the pump can't outlet water due to the air in it.

It's equipped with a brushless motor providing smooth and quiet operation than a non-brushless water pump. The example project of the soil moisture Sensor Module working with Arduino Uno R3 and Raspberry pi can be provided free by Email, please contact us via Amazon. Application:supports all mCU control, PLC control, The industrial field, Smart home control.

Decdeal Submersible Water Pump DC 12V 5W Ultra-quiet Pump for Pond, Aquarium, 280L/H Lift 300cm #ad - Indication LED's for Relay output status. Module output is high level when the soil moisture deficit, or output is low. Current: 416mA Max. It can be used in the water or other liquidswithout particles and impurities; NOT for viscous and acid-base liquids. It's normal and safe phenomenon. Can be used in module plant waterer device, and the plants in your garden no need people to manage.

Brushless, permanent magnetic rotor, maintenance-free. Stator and circuit board sealed by epoxy resin.

Weitere Informationen zu Anself H10448 #ad


Similar products:

• Learn To Brew LLC Food Grade Vinyl Tubing - 10 feet 5/16 ID - 7/16 OD #ad
• Eldon James T0-5NN Natural Nylon Equal Barb Tee, 5/16" Hose Barb (Pack of 10) #ad
• Dial 3073 DuraCool Cooler Pad, 29" x 30" #ad
• Dial 3005 Mfg. Aspen Cooler Pads #ad
• XSPC G1/4" to 3/8" Barb Fitting Black Chrome - 4 pack #ad
• HONG111 5pcs TE215 Dual Mode High Sensitivity Soil Moisture Sensor, Auto Arduino Sensor Module Watering System Manager 3.3V-5V #ad
• 10 Feet - 5/16" ID 7/16" OD Clear Vinyl Tubing FDA Approved Food Grade Multipurpose Tube for Beer Line, Kegerator, Wine Making, Aquaponics, Air Hose by Proper Pour #ad
• Anself Ultra-quiet Mini 4.8W DC12V Micro Water Oil Pump Submersible (Style 3) #ad
• ZJchao 200ml Acrylic Water Tank Cooler Water Cooling Radiator Pc Cpu Water Block #ad
• uxcell 5 Pieces ZP4510 Liquid Water Level Sensor Vertical Float Switches #ad